![]() I’ve got one body where the winder slips. Some of the components won’t work and you will need to swap them out. And that’s a good thing, because when some of the components don’t work you can swap them out. I wanted square format, something solid, with a decent range of decent lenses, and not too ancient.īronica SQ-A without speed grip. Hasselbald, Mamiya, Contax, Pentax all too expensive. I wanted a new toy, so I decided to give 120 another chance. Light leaks (the Autograph, but then it is circa 1920).Gummy shutters (my Rolleis are long overdue servicing).Turns out my old Weston light meter is unreliable.And I’ve tried lots of 120s since then Rolleiflex, Hasselblad, Kodak autograph. Thanks again to all of you who offered suggestions.One of the first cameras I owned was an Ensign Selfix 120. I'm going to try putting a women's elastic headband around the join where the insert fits into the holder, hoping that might do the trick. I wrote to Jon again, and he's just stumped. The parts of the test roll that I shot in shady streets showed no leaks at all. It's true it only does this if exposed to bright sunlight for a while. Yesterday, however, I shot a roll of film using the back, and still it leaks. When he sent it back, I found the seals were actually now in better shape than the other Bronica back I have, which doesn't leak at all. He not only looked it over, he actually replaced some seals that he thought weren't quite right. Jon was helpful guiding me through the process, and when I wrote to him that the repair wasn't successful, he generously offered to look it over. I then tested the back again - the film still showed light leaks, same if not worse. I installed the new seals, which was sort of fiddly - lots of small pieces. It has not turned out well.Īs I mentioned the last time, I got the Jon Goodman light seal kit for this Bronica SQ back. It's been a while since I started this thread, so I thought I'd post an update for those of you who gave me advice. One suspects there is a repair manual for backs that might show what Bronica thought should be there seal-wise, but I've never found one. ![]() The leak was hitting the film between the supply spool and the roller it was the subsequent frame where all hell let loose. On the roll that led to the "Oh my back!" photo on that page of mine, the first frame was fine, as the film was loaded in the house in relatively subdued light and wound to the first frame. In general the degree of effect of leaks can vary with the orientation of the camera, ambient light intensity and how quickly one winds to the next frame. That appears to be a fairly mild leak which makes it more difficult to track down. If the orientation of the original photo is as the scene looks in the OP (my original assumption), the image on film is upside down and reversed right to left, putting the leak on the side away from the dark slide suggesting a hinge seal problem (unless the camera was used upside down!!!) I am still a bit uncertain about this leak analysis. The one seal area that doesn't cover is the dark slide - mostly because I have yet to be forced to open that up! I now have four backs, I guess I could risk getting out a screwdriver, except I think I need to splurge on some of the 'official' JIS flavors. Hehe, that's me, thanks for the compliment. If anyone has any ideas about this, I'd be very grateful. I doubt that I let light into the film roll as I was loading or unloading the insert (twice), because the leak appears on exactly the same spot on each frame. The condition of the Sq-Ai back appears identical to the other back that is light-tight. Plus I can't see any tiny holes or cracks that might be causing this. ![]() I checked the back carefully and all the light seals are fine. The leak appears in the same spot on every frame (upper left), but varies in intensity, sometimes quite noticeable, sometimes barely. The film from the other back showed no leaks. I've used both without problems for several months, but the last two times I used both, the developed film from the SQ-Ai back showed some sort of light leak on every frame. I have a Bronica SQ-B with its original 120 back, plus an extra 120 back for an SQ-Ai.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |